Repair instructions
    Body Structures
    Body Panels and Closures
    Body Exterior
    Chassis
    Powertrain
    Electrical
      Wiring Harness
      Electrical Systems
      Electrical Hardware
      Infotainment
        Infotainment Service Procedures
        Sound System
        Antenna System
        ADI ECU System
          DA-RM-07M021-04-001 - Remove/Install control unit - Displays
          DA-RM-07M021-04-002 - Remove/Install control unit - Infotainment
        Displays
        Cameras
        Infotainment External Interface
      Electrical Misc
    Interior
    Accessories
    PDI/Service/Track/Technical Sheets
    Paint Technical Data Sheets
    Wiring Schematics
  Customer Service
Instructions
Electrical / Infotainment / ADI ECU System / DA-RM-07M021-04-001 - Remove/Install control unit - Displays
Preparation work
1.     
2.     
3.     
Care Point: Remove both sides.
4.     
Care Point: Remove both sides.
5.     
6.     
7.     
8.     
Care Point: Remove both sides.
9.     
10.    
11.    
12.    
13.    
Remove control unit - Displays
 
Care Point:
Wiring harness clips tight.
 
1.   
Detach lower wiring harness clips from bracket (1).
 
2.   
Remove nuts (2).(M4) 5 Nm
 
3.   
Detach upper wiring harness clips from bracket (3).
 
4.   
Remove bracket (4).
 
 
Care Point:
Remove the left bracket only.
 
5.   
Remove bolts (5).(M6x12) 8 Nm
 
6.   
Remove bolts (6).(M5x12) 2 Nm
 
7.   
Remove bolts (7).(M5x16) 3 Nm
 
 
Care Point:
Bracket will be removed with front parking speaker attached.
 
8.   
Disconnect electrical connector from front parking speaker.
 
 
Care Point:
Harness is clipped to bracket both inside and outside.
 
9.   
Detach wiring harness from bracket.
 
10.  
Remove bracket (8).
 
11.  
Remove bolts (9).(M5x12) 2 Nm
 
12.  
Disconnect electrical connectors from control unit.
 
13.  
Remove the control unit (10).
 
Install control unit - Displays
 
Care Point:
Check and replace any damaged harness clips.
 
1.   
Install components in reverse order.
 
 
Care Point:
Carry out steps 2 to 15 if a new control unit is fitted.
Care Point:
Make sure VCI and MDS batteries are in good condition or connected to external power supply.
 
2.   
Connect McLaren Diagnostic System (MDS).
 
3.   
Proceed to Diagnostic Toolbox within Advanced Driver Interface (ADI).
 
 
Care Point:
If update is not available, proceed to step 10.
Care Point:
Do not attempt to start reprogramming until the Ethernet cable is installed correctly.
The OBD2 cable must remain connected to the vehicle and MDS tablet during the entire reprogramming process.
 
4.   
Access Reprogramming.
 
5.   
Using tool kit Tool - MDS Download Adaptor, plug the Ethernet cable into the MDS tablet.
 
6.   
Install the supplied Ethernet to USB male adaptor to the Ethernet cable.
 

7.   
Plug USB adaptor into port one (P1) of the USB interface panel, located in the tunnel console.
 
 
Care Point:
ADI screen will display "Update Preparing".
 
8.   
Allow update to download to the ADI system.
 
 
Care Point:
ADI screen will display progress bars during install, followed by "Update Successful" once complete.
 
9.   
Allow update to install to the ADI system
 
10.  
Access Sequences.
 
11.  
Carry out Align Car Configuration sequence.
 
12.  
Carry out Programme VIN sequence.
 
13.  
Carry out Set Configuration Defaults sequence.
 
14.  
Carry out Radio Configuration sequence.
 
 
Care Point:
Where required, check and re-calibrate vehicle camera system.
 
15.  
or
 
16.  
Read out and clear error memory.
 
17.  
Check functionality.
 
   
   
   Note